Cascadian Flintkote PF-4 Bitumen Paint
Cascadian Flintkote PF-4 Bitumen Paint Cascadian Flintkote PF-4 Bitumen Paint Johor Bahru JB Malaysia Supply Suppliers Manufacturers | Cascadian Asphalt Industries Sdn Bhd
Cascadian Flintkote PF-4 Bitumen Paint

Price: USD 625/-(FOB, Pasir Gudang, in A+ Drums. Valid until 30/09/2015)
USD 595/-(FOB, Pasir Gudang, in A   Drums. Valid until 30/09/2015)




Cascadian Flintkote PF-4 Bitumen Paint is low viscosity blend of selected hard grade bitumen in solvent which dries to form a high quality tough bitumen film. (Note: Cascadian Flintkote PF-4 Bitumen paint is formerly marketed underCascadian PF-4 bitumen paint. Product quality and specification remains unchaged)


USAGE
As vapour barriers, damp proof courses, linings to potable water tanks and pipes to provide a continuous barrier to the passage of water and water vapour. Corrosion protection to metal surfaces such as “I” beam for piling, steel piles and drinking water tanks etc.

Concrete protection:
As a primer to concrete roofs, cement screeds/renders, bitumen felt, mastic asphalt prior to application of other bituminous coatings. To rejuvenate bituminous felts or asphalt surfaces which have been oxidised.



TECHNICAL ADVANTAGES
  • Easy and inexpensive to apply

  • Does not taint water

  • Quick drying

  • Excellent adhesion to common building substrates

  • High coverage rates

  • Tough bitumen film formed

    STANDARD COMPLIANCE

  • BS3416 Type I Class C: British Standard For Bitumen-Based Coating.
        For Cold Application, suitable for use in contact with potable water.

  • BS6949 Type I Class C: British Standard For Bitumen-Based Coating.
        For Cold Application, excluding use in contact with potable water.


    SPECIFICATION CLAUSE
    Bituminous or concrete surfaces areas so designated
    shall be coated with Cascadian Flintkote PF-4 bitumen paint
    as supplied by Cascadian. The coating should be applied in a
    minimum of 2 coats at a coverage rate not less than 10 m2/litre per
    coat in accordance with the Cascadian’s current product data sheet.



    APPLICATION INSTRUCTION
  • Surface Preparation
        All surfaces shall be clean and free from dust, dirt, oil,
         grease, moss and loose material.

  • Coating Application
         Apply a minimum of two thin coats by brush, roller or
         conventional spray equipment. Allow first coat to dry before
         applying second coat at right angles to the first coat. When
         used as the primer, apply only one coat and allow to dry.



    COVERAGE
    Coverage rates will vary depending on the actual surface
    environment and application. The typical coverage is about
    1.5 litres/m2 for a 2 coats application.



    HEALTH AND SAFETY


  • Flammability: Flammable. Keep away from sources of ignition
    including pilot lights and sparks. Take precautionary measures
    against static discharge. Do not smoke. Keep containers tightly
    closed when not in use. If used in an enclosed space, ensure
    thorough ventilation of the area (using flame proof mechanical
    blowers) to avoid any accumulation of vapour until the product
    has dried. In case of fire use dry powder, carbon dioxide, foam,
    sand or earth. Never use water as this may spread the fire.
    (Note: Electric motors, light/power switches and steel tools may
    generate sparks sufficient to ignite such a material or the vapours
    given off, resulting in an explosion and/or fire.)


  • Skin Contact: Contains solvents which cause defatting of the
    skin and, in extreme circumstances, dermatitis. Avoid contact by
    careful working and use of barrier cream or gloves. Remove skin
    contamination with a proprietary hand cleaner following by washing
    with soap and water.


  • Eye Contact: Could be harmful. Wear protective eye-shields,
    especially where there is a danger of splashing. In the event of
    accidental contact, irrigate the eyes immediately with clean water
    for 15 minutes and seek medical attention.



    BITUMINOUS PROTECTIVE COATING & PRIMER


  • Inhalation: Contains low volatility solvents. Use in
    well ventilated areas and avoid inhalation and use
    suitable respirators or breathing mask where necessary.
    In the event of discomfort as a result of inhalation, remove
    person to fresh air and obtain medical attention.


  • Oral Digestion: With proper handling oral digestion
    should not occur. The possibility can be minimised by
    not consuming food in the working area and by washing
    hands thoroughly before eating, drinking and smoking.


  • Spillage: Spilt material should be mopped up immediately
    with an inert absorbent material such as sand and disposed
    of, in accordance with local regulations, by incineration or burial.


  • Disposal of Containers: Do not leave empty containers on
    site where any residue could be a hazard to children or animals.
    Replace lids and remove all containers to a central disposal point.



    STORAGE
    A minimum of 12 months in original sealed containers stored under cover
    in a cool and dry place. It must be stored under conditions which meet the
    local regulation applying to such substances.



    PRODUCT DATA SUMMARY (Property Test Typical Values)
    Type of Solvent - Petroleum Hydrocarbon
    Flash Point - 36°C
    Solid Contents - >50%
    Specific Gravity - 0.90
    Film Tickness - wet : 100 microns; dry : 54 microns
    Application Temperature Range - -5°C to 55°C
    Drying Time - BS3416/6949:1991 Approximately 1 hour, depending on temperature humidity, air change and base conditions
    Finish - BS3416/6949:1991 Smooth, opaque and free from sags or runs.
    Tap Water immersion resistance - BS3416/6949:1991 Passed
     
  • 4 Days Immersion - The film remained completely adhered to the substrate.
     
  • 14 Days Immersion - No blistering was observed. No visible rut or pitting on
          the exposed metal surface.

    Artificial Sea Water Immersion Resistance - BS3416/6949:1991 Passed
     
  • 4 Days Immersion - The film remained completely adhered to the substrate.
     
  • 14 Days Immersion - No blistering was observed. No visible rut or pitting on
          the exposed metal surface.

    Blending Resistance - BS3416/6949:1991 Passed.
                                              No Signs of cracking or detachment from the substrate
    Effect on Portable Water - BS3416:1991/BS6920:2000 Passed.
                                                      Suitable for use in contact with portable water.

    Typical values may represent average values from samples tested.


    DRUMMING OPTIONS
    (Grade A+) Brand New Drum

    (Grade A) Recondition Drums . 
    External painted in Black   
    Internal washed and 100% cleaned

    (Grade B) Recondition Drums .
    External painted in Black
    Internal containing 2 to 3 Kg
    Foreign material .

    (Grade C) Recondition Drums .
    External unpainted .
    Internal containing 2 to 3 Kg Foreign material .

Please leave your enquiry here, we will reply as soon as possible.


*only support gif, jpeg, jpg, png, pdf
Switch To Desktop Version